Welkom bij www.woodworking.nl.
Resultaten 1 tot 3 van de 3

Onderwerp: workshop build

  1. #1

    workshop build

    Hey Guys,

    I've just started constructing a workshop on my own (hopefully) common healthy sense.
    No engineer, architect, code or whatever to into account.
    The workshop is build inside an existing building (old garage shop) and designed to take appart in a few years and move it to my future building site.

    I'm going to use 2x6's at 24" center to have a bit more insulation.

    -9' 10" wide by 8' 2" garage door
    -3' 3" wide by 7' 2" high outside door
    -3' 1" wide by 2' 5" high window


    The wall disection is as follows:
    wall disection.jpg



    Most importand thing is that I want my walls to be vapour open (hope the osb supplier gives me air tight sheets)
    Sidings and inside wall finishing will be decided in the future, because the construction will be indoors (outside woodfiber sheet can withstand constant water/moisture up to 4 weeks guaranteed).
    The STEICOflex and STEICOuniversal productes can be found at http://www.steico.com/en/products.html

    The floor is just a thick concrete slab (2 or 3 anchor bolts /wall element) and because I'm also going to do some welding I would like to keep it that way and not go for wooden flooring.



    Garagedoor header
    Is it possible to construct a 2x6" flat truss system and use it as a header (have a lot of 2x6's) : cheapest solution and I should probably increase the number of cripples used in sketchup.
    or should I stick with the LVL/gluelam headers
    In beginning I was thinking about framing 3 2x6's against eachother and sandwich this beam between 2 2x6's so you should end up with 6x10"
    garagedoor.jpg
    note: no sheeting (except in door/window opening), sil- and topplate in drawings.



    Outside door + header
    First I wanted to let the door slide on the concrete floor but perhaps to avoid problems in the future at future location I've raised the door to make it flush with the sil plate including a 23/32" marine grade plywood sheet.
    The door itselfe is incased in a marine grade plywood box (bottom of box is mounted directly on the silplate) to have a stiff air tighter insulated door frame.
    Doorframe is going to be taped windtight against the STEICOuniversal.
    There is a 10mm gap between the plywood frame and STEICOuniversal to shim the door straight and fill with insulation afterwards.
    Headerwise I tought about having 2x6's ripped to 2x3 1/2" nailed 3 behind each other.
    doorframe.jpg
    door detail.jpg
    note: no sheeting (except in door/window opening), sil- and topplate in drawings.


    Window opening
    The window opening is the same as the door opening apart from the header here that consists of 3 2x6's behind each other and a 2x6 nailed on top.
    windowframe.jpg


    I'm not sure about what I would do with the walopening between the low and high part, there is probably a 2nd floor going on top of the low part if there is enough height (can only see this after 1st floor construction because the complete construction is build under an existing roof)
    After wall framing is done, I'll tackle the roofing problems for the workshop.
    workshop.jpg
    workshop2.jpg


    Any suggestion/question is welcome!

  2. #2
    So far no questions or suggestion but it will be interesting following your build. I doubt you will ever move a building like this to a future site... This seems like the building that for fills your wishes without doing any compromises to its mobility. Nevertheless, maybe anyway one suggestion though... get rid of measuring in inches!

  3. #3

 

 

Forum Rechten

  • Je mag geen nieuwe onderwerpen plaatsen
  • Je mag geen reacties plaatsen
  • Je mag geen bijlagen toevoegen
  • Je mag jouw berichten niet wijzigen
  •  
This website uses cookies
We use cookies to store session information to facilitate remembering your login information, to allow you to save website preferences, to personalise content and ads, to provide social media features and to analyse our traffic. We also share information about your use of our site with our social media, advertising and analytics partners.
     
Back to top